Toyota Highlander Service Manual: Oil pump seal (3MZ-FE)

Toyota Highlander Service Manual / Emission control / Oil pump seal (3MZ-FE)

REPLACEMENT

1. REMOVE FR WIPER ARM LH (See page 66-7 )

2. REMOVE FR WIPER ARM RH (See page 66-7 )

3. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSY (See page 66-7 )

4. REMOVE WINDSHIELD WIPER LINK ASSY (See page 66-7 )

5. REMOVE COWL PANEL SUB-ASSY

6. REMOVE FRONT WHEEL RH

7. REMOVE ENGINE UNDER COVER NO.1

8. REMOVE FRONT FENDER APRON SEAL RH

9. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See page 14-125 )

10. REMOVE VANE PUMP V BELT (See page 14-125 )

11. REMOVE ENGINE MOVING CONTROL ROD (See page 14-149 )

12. REMOVE ENGINE MOUNTING STAY NO.2 RH (See page 14-149 )

13. REMOVE GENERATOR BRACKET NO.2

14. REMOVE CRANKSHAFT PULLEY (See page 14-173 )

15. REMOVE TIMING BELT NO.1 COVER

16. REMOVE TIMING BELT NO.2 COVER (See page 14-206 )

17. REMOVE ENGINE MOUNTING BRACKET RH

18. REMOVE TIMING BELT GUIDE NO.2

19. REMOVE TIMING BELT (See page 14-206 )

20. REMOVE CRANKSHAFT TIMING PULLEY (See page 14-173 )

21. REMOVE OIL PUMP SEAL

REMOVE OIL PUMP SEAL

(a) Using a knife, cut through the oil seal lip.

(b) Using a screwdriver with its tip wrapped in tape, pry out the oil seal.

NOTICE: After the removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.

22. INSTALL OIL PUMP SEAL

(a) Apply MP grease to a new oil seal lip.

NOTICE: Keep the lip free of foreign matter.

INSTALL OIL PUMP SEAL

(b) Using SST and a hammer, tap in the oil seal until its surface is flush with the oil pump edge.

SST 09223-00010

NOTICE:

Be careful not to tap the oil seal slantingly.
Wipe off extra grease on the crankshaft.

23. INSTALL CRANKSHAFT TIMING PULLEY (See page 14-173 )

24. INSPECT TIMING BELT (See page 14-206 )

25. INSTALL TIMING BELT (See page 14-206 )

26. INSTALL TIMING BELT TENSIONER ASSY (See page 14-206 )

27. INSTALL TIMING BELT GUIDE NO.2 (See page 14-206 )

28. INSTALL ENGINE MOUNTING BRACKET RH Torque: 28 NVm (286 kgfVcm, 21 ftVlbf)

29. INSTALL TIMING BELT NO.2 COVER (See page 14-206 )

30. INSTALL TIMING BELT NO.1 COVER (See page 14-206 )

31. INSTALL CRANKSHAFT PULLEY (See page 14-173 )

32. INSTALL GENERATOR BRACKET NO.2 Torque: 28 NVm (286 kgfVcm, 21 ftVlbf)

33. INSTALL ENGINE MOUNTING STAY NO.2 RH (See page 14-149 )

34. INSTALL ENGINE MOVING CONTROL ROD (See page 14-149 )

35. INSTALL VANE PUMP V BELT (See page 14-125 )

36. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See page 14-125 )

37. INSPECT DRIVE BELT TENSION (See page 14-121 )

38. INSTALL COWL PANEL SUB-ASSY

39. INSTALL WINDSHIELD WIPER LINK ASSY (See page 66-7 )

40. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSY (See page 66-7 )

41. INSTALL FR WIPER ARM LH (See page 66-7 )

42. INSTALL FR WIPER ARM RH (See page 66-7 )

43. INSTALL FRONT WHEEL RH

44. CHECK FOR ENGINE OIL LEAKS

Cylinder head gasket NO.2 (3MZ-FE)

REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 11-35 ) 2. DRAIN ENGINE COOLANT (See page 16-26 ) 3. DRAIN ENGINE OIL 4. REMOVE FR WIPER ARM LH (See page 66-7 ) 5. REMOVE ...

Engine rear oil seal (3MZ-FE)

REPLACEMENT 1. REMOVE AUTOMATIC TRANSAXLE ASSY (2WD TYPE) (See page 40-20 ) 2. REMOVE AUTOMATIC TRANSAXLE W/TRANSFER (4WD TYPE) (See page 40-20 ) 3. REMOVE DRIVE PLATE & RING GEAR SUB-ASSY ...

More about Toyota Highlander:

Using the rear view monitor system
Screen description The rear view monitor system screen will be displayed if the shift lever is shifted to r while the engine switch is in “on” position. Vehicle width guide lines the line indicates a guide path when the vehicle is being backed straight up.The displayed width is wid ...